December 11, 2024
 

Slide 1 Slide 1 Slide 1 Slide 1 Slide 1 Slide 1 Slide 1 Slide 1
Search
Technology/Function
Form Factor
Interface
IP Core
NKS-V016-C

Stand-Alone Board
Virtex-6 & DSP High Performance Processing Platform
8- Channel 16-bit ADC 125MSPS
4- Channel 16-bit DAC 1GSPS
 
 
Description

The NKS-V016-C processing board is a high performance industrial single card dedicated to high performance data acquisition and communications based on the Xilinx Virtex-6 SX315T FPGA family. The NKS-V016-C board enables designers to prototype high-performance digital transceivers. The board includes a DSP Processor (TMS320C6678) which incorporating the new and innovative C66x DSP core, this device can run at a core speed of up to 1.25 GHz. Additionally four D/A channels 16 bit resolution at maximum rate of 1GSPS per channel and eight A/D channels 16 bit resolution at maximum rate of 125 MSPS per channel are available. The sample clock can be supplied from PLL clock distributer, externally through a coax connection or supplied by an internal clock source.


 
Features

ADC's:

  • 8 Channels, 16 bit, 125MSPS
  • Differential Analog Input with 650MHz Bandwidth
  • Analog Input Filter Options
  • SNR = 75 dBFS @ 20 MHz and 125 MSPS
  • SFDR > 80 dBc @ 20 MHz and 125 MSPS
  • ENOB = 12.4 Bits @ 20 MHz and 125 MSPS
  • Xtalk Isolation > 95dB
  • Low Power: 750 mW @ 125 MSPS
  • High Performance AC-Coupled Analog Input
  • 1.8 V Analog Supply Operation
  • 1.8 V CMOS or LVDS Output Supply
  • Flexible Analog Input Range: 1V p-p to 2V p-p
  • Pin Compatible with AD9650

 

DAC's:

  • 4 Channels, 16-Bit, 1GSPS Update Rate
  • Analog Output with 500MHz Bandwidth
  • Analog Output Filter Options
  • Phase Noise > 100dBc @ 1kHz and 1GSPS
  • Interleaved I/Q data for Dual-DAC Mode
  • 2x-32x Clock Multiplying PLL/VCO
  • 2x or 4x Interpolation Filters
  • High Performance AC-Coupled Analog Output with 2 Channel AC/DC Coupled Switching Capability

 

Clock's:

  • Flexible Synchronous PLL Clock Tree withInternal orExternal Clock
  • On board 200MHz Oscillator

 

Processor's:

  • Virtex XC6VSX315T-1FFG1759I Xilinx Device
  • Digital Signal Processing (DSP) TMS320C6678 TI Device
  • ARM Microcontroller AT91SAM7X256 Atmel Device
  • SP3XC3S200AN-4FTG256I for Power Sequence and DSP Separate Configuration

 

Memory's:

  • 4 Gb DDR3 Component Memory (Two [256 Mb x 8] Devices) for Virtex-6 FPGA
  • 8 Gb DDR3 Component Memory for DSP
  • 1 Mb I2C EEPROM for DSP local boot (remote boot possible)
  • 128 Mb NOR Flash for DSPSPI local boot
  • 144 Mb @ 167MHz SRAM Component Memory (Two [4Mb x 18] Devices)

 

Interface's:

  • Ethernet PHY 10/100/1000 Interface with RJ-45 Connector for FPGA and DSP
  • GPIO, EMIF, SRIO and PCIe Interface between FPGA and DSP
  • On-Board XDS100 type Emulation using High-speed USB 2.0 interface for DSP
  • RS232/RS485 UART for DSP
  • 2x 60mA Buffered TTL OUT
  • 8x Buffered TTL IN and 8x Buffered TTL OUT
  • 20x RS422, 9x RS485, 24x GPIO and 1x CAN BUS Serial Interfaces

 

Other's:

  • Multi-boot Configuration
  • Status and Debug LEDs
  • Power on/off Slide Switch
  • Physical Dimensions (L: 249.9 mm, W: 233.2 mm)
  • Operating temperature: -40°C to +85°C (Industrial)
  • 8V~ 15V External Voltage Supply
  • Maximum Power Consupmtion in Full Load: 160W
  • Operation System Support: Windows & Linux





 
Block Diagram
niksoo
 
Application

 

• RADAR/SONAR
• Communications
• Diversity radio systems
• Multimode digital receivers (3G)
• GSM, EDGE, W-CDMA, LTE
• General-purpose software radios
• Broadband data applications
• I/Q demodulation systems
• Fire Control and Defense Systems
• Smart antenna systems

 
Documents
Download
NIKSOO Wave Processing Technology Engineering Corporation operates in the field of Biomedical, electronics and telecommunication, base-band and signal processing, installation and lunching, consulting and software production.
  btndownload


© copy right 2012 &all rights reseved by NIKSOO Wave Processing Technology Engineering Corporation